How To Make A Tattoo Gun At Home?
Developing the Components – 1. Locate a motor. You’ll need an electric motor or equivalent rotational motor that works on at least 12 volts; 18 volts is preferable.
- A tiny shaft will protrude from the middle of the engine. Attach a little four-hole button to the shaft using superglue. Take care not to apply so much glue that it leaks through the button holes and plugs them. They must be open so that you can insert the needle. Remove it from the oven and set it aside to dry.
- You may use an eraser instead of a button. Take the eraser from a mechanical pen and firmly press it on the little shaft of your motor.
- You may remove the motor from a VCR or remote control vehicle, but the power will be much reduced; it will be about 3. 5 volts.
2. Make the tube. The needle will be guided by the “tube. ” It’s simple to construct one out of a pencil or pen.
- Make use of a mechanical pencil. A cheap plastic pencil will suffice, or you may use a metal pencil. You may leave the pencil as is or trim it down to around a 3″ to 4″ length, depending on your desire.
- You may also use a regular stick pen, such as a Bic, and remove the ink cylinder from the inside. If you desire a shorter tube, trim the pen to 3″ or 4″ in length. File down the brass tip of the pen to get the ball out and create the hole large enough for the needle to slide through.
3. Create a brace. When the tube is connected to the tattoo gun’s machine motor, the brace will provide support.
- Break off a teaspoon from the bowl (the part you eat from). Then, bend the spoon back into a “L” form.
- A second approach is to remove the bristles from a toothbrush, leaving approximately 4″ of bristle length. Warm up the plastic toothbrush handle with a lighter and bend it into a “L” shape. Keep the bent handle in place until the plastic cools and stiffens.
4. Create a needle. Make a metal guitar string about an inch longer than the length of your tube. After assembly, it should extend from the center of the motor to the tip of the tube. Bring the soap and water to a boil in a kettle. Put your needle in the kettle and bring it to a boil for five minutes.
- You may prepare multiple needles ahead of time. If you do this, be sure to preserve them in a sterile container.
Contents
What can I make a tattoo gun out of?
Can you tattoo without tattoo gun?
Download Article Download Article If you can’t afford a professional tattoo or you don’t have access to a tattoo parlor, you can give yourself a tattoo at home without a tattoo gun, using what is sometimes called the “stick-and-poke” method. This process can be dangerous, however, and if it turns out badly, you’re left with a permanent reminder. Be sure you know what you’re doing and make sure to follow all of the safety warnings and sanitation requirements before you try this yourself.
- 1 Buy or assemble a home tattoo kit. The main components of any home tattoo kit are needles and ink. Only use tattoo needles that haven’t been used. Tattoo ink is the only type of ink you should use, but not always easy to find. India Ink is commonly used as calligraphy ink but is the only ink that is not tattoo ink that can be used as tattoo ink. Don’t use pen or marker ink! [1]
- Home tattoo kits are the safest option, are inexpensive, and include both supplies and instructions.
- Find a reputable brand of tattoo ink to ensure it doesn’t contain any toxic ingredients.
- Don’t use sewing needles, straight pins, or safety pins. They are not sterile, even if they are new. It is extremely dangerous to use any of these objects to tattoo yourself. You may end up in the hospital. They don’t hold the ink well and generally aren’t the right type of needle. You need to be as professional as possible if you are going to do this yourself. [2]
- Don’t use old needles. Don’t share needles. Doing either of these will put you at serious risk for infection. Also, be sure to safely dispose of the needles when you’re done.
- 2 Set up your station. You’ll need a few other things before you start putting needle to flesh. Grab some cotton thread, a cup for water, and rubbing alcohol. [3]
- Keep a non-permanent, non-toxic marker around for drawing potential tattoo ideas. [4]
- It’s a good idea to keep ink caps, a shallow bowl, or saucer handy to pour India ink into. Ink caps are inexpensive and can help prevent you from wasting ink. Sterilize with rubbing alcohol or hydrogen peroxide that is 91-99% alcohol.
- It’s important to make sure everything you use is clean. Wash any bowls or saucers you’ll be using in hot, soapy water and peroxide/rubbing alcohol, and then cover them with plastic wrap. For extra protection, wear gloves that are very well sterilized when handling any of the supplies you’ll be using. Wash gloves (if using) and hands multiple times throughout the whole process.
- 3 Clean and shave your chosen area. Wherever you decide to tattoo yourself, clean it with soap and warm water. Shave the hair off in the area about an inch larger than you want your tattoo to be.
- After you shave, sterilize your skin with rubbing alcohol. Dab it on with a cotton ball and make sure it’s evaporated before continuing.
- 4 Draw the design on your skin. Trace or draw your desired tattoo in the place you want it to go. You can have someone else do it for you if you want, but take the time to get it how you want it. This image is all you’ll have to go on once you start. You can also use stencil paper and stencil gel to make it more accurate.
- Since you’ll be tattooing yourself, make sure the place you choose is easily. You WILL be poking for a few hours. Awkward or hard to reach places on the body, such as your chest or shoulder, are never good ideas for stick ‘n’ pokes on yourself.
- Stick ‘n’ pokes work much better with simple and tiny tattoos. If you want a complex tattoo, you’re better off going to a parlor.
- 1 Sterilize the needle. The best way to sterilize the needle before using it is with flame. Hold the needle over the flame of a candle or a lighter until it glows. Make sure you hold the other end with tongs, or you’ll burn your fingertips. [5]
- Once the needle is sterile, wrap it in cotton thread. Start about 1 ⁄ 8 inch (0. 3 cm) away from the tip and wrap the thread back and forth about 1 ⁄ 4 inch (0. 6 cm) up the needle until the thread has formed an oval shape. This will absorb some of the ink as you dip your needle into the saucer. [6]
- 2 Start poking. Dip the needle into the India ink and then poke it through your skin, leaving a small dot. There may be some blood after several layers of poking, but there shouldn’t be much. If blood is dripping/excessive, stop immediately and sterilize. Hold a clean paper towel, not cloth, onto the tattoo until it stops bleeding.
- 3 Start working your way along the lines. Stay inside the line of the tattoo design you’ve drawn, filling it in with tiny punctures. Use a cotton swab or a rag to wipe away any blood or excess ink. [7]
- The skin may swell up a bit as you poke it which may cause the resulting tattoo to appear spotty. You may have to do touch-ups when the swelling goes down if you want smooth lines throughout the tattoo. Wait to do touch ups until after the tattoo is completely healed, which can take up to two months.
- 4 Clean the tattooed area. When you finish the tattoo, wipe down the area with soapy water. Throw away any remaining India ink in the ink cap and needles. They are no longer sterile. Use a new needle and a new saucer of ink if you plan on doing any touch-ups in the future.
- Avoid cleaning a fresh tattoo with alcohol — use soap and water, instead.
- 1 Bandage your new tattoo with saran wrap. Don’t use a cloth or band-aid as they can absorb some of the ink and fade it faster. Don’t use any ointments or lotions for the first week of healing because they can clog the tattoo and puts it at risk of infection. [8]
- Leave the wrap on for 1-3 hours, but no longer than 6. [9]
- 2 Keep your tattoo clean. Remove the initial wrap and gently wash the area with warm water and non-scented soap. Don’t scrub, and only wash the tattoo with clean hands. [10]
- Don’t soak your tattoo and don’t run it under hot water. It won’t feel nice, and it take the ink out of your skin. [11]
- Avoid picking at the tattoo as this could cause some of the ink to bleed out, causing messy lines and even scarring.
- Make sure to remove the bandage and wash the tattoo after a couple of hours.
- 3 Apply lotion to your tattoo. After the swelling goes down and the skin starts to scab, switch to a plain, unscented lotion. Most professionals recommend Lubriderm or Aquaphor. Keep the layers thin. Your skin needs to breathe so it can heal properly.
- Moisturize your tattoo 3-5 times a day depending on the size of the tattoo. If your skin starts to look dried out, use a small amount of lotion. [12]
- Don’t apply anything that’s too greasy, like vitamin E, aloe, or Vaseline.
- 4 Let your tattoo heal. For the first week or so be mindful of your tattoo. It’s going to scab over and you’ll need to take extra care to keep it clean. In addition to washing it and keeping it moisturized, you’ll need to avoid certain activities. [13]
- Keep your tattoo out of direct sunlight, as this can cause the ink to fade. It will also burn like a bad sunburn.
- Avoid pools of water such as baths, hot tubs, pools, lakes, oceans, etc. They are full of bacteria, which can lead to infection. [14]
- Avoid any activity that is high-contact or induces excessive sweating, like working out. [15]
- Wear loose clothing so your tattoo can breathe. Tight clothing prevents this.
- 5 Watch out for infection. Be on the lookout for redness or excessive scabbing around your tattoo, as well as any oozing, or swelling. These are all signs of possible infection. [16]
- You can minimize the risk of infection by keeping your supplies clean and taking care of your tattoo. Still, it is possible your tattoo could become infected. If you suspect that your tattoo has become infected, consult your physician. [17]
- Make sure that you aren’t picking or scratching at your tattoo, either.
Add New Question
- Question Is it 100% permanent or will it go away completely after a few years? Kiara Hamed is a Tattoo Artist based in Dallas, Texas. She has over nine years of tattoo designing experience. She received her Tattoo Artist Certification in 2010 and a BS in Computer Information Systems from Clark University Atlanta in 2013. Tattoo Artist Expert Answer It may fade over time but it’s not guaranteed to go away completely. Tattoos are permanent.
- Question How far apart should the pokes be? Kiara Hamed is a Tattoo Artist based in Dallas, Texas. She has over nine years of tattoo designing experience. She received her Tattoo Artist Certification in 2010 and a BS in Computer Information Systems from Clark University Atlanta in 2013. Tattoo Artist Expert Answer Try to make them as close together as possible so you cover the entire intended area. Otherwise, the tattoo will be splotchy.
Ask a Question 200 characters left Include your email address to get a message when this question is answered. Submit.
What can I use as a tattoo needle?
Stick and Poke Tattoo Needles – The most common stick and poke tattoo technique, commonly called the ” needle and thread tattoo technique ” consists in inserting a sewing needle right between a pencil’s eraser and the metal socket. The dental floss is then rolled around the needle to create an ink container. 
With a careful use of dental floss and proper needle sharpening, you can get away with tattooing using sewing needles. However, these tools aren’t optimal for stick and poke tattoos since they don’t retain ink as well as tattoo needles and aren’t as sharp. Moreover, they are imprecise and less hygienic. In my experience, the simplest and most enjoyable way to proceed is to use stick and poke tattoo needles.
How do you make a tattoo gun out of an electric toothbrush?
How much does tattoo gun cost?
Tattoo Gun Cost – If you already have access to some supplies, you may only need to buy a tattoo gun. The average cost for a tattoo machine is $400 to $900, and that doesn’t include the cost for other tattoo supplies. You’ll get an excellent quality tattoo gun for that price, though.
Can I use pen ink for a tattoo?
Pen Ink – With the number of art stores and online warehouses that you can purchase from, pen ink should never be an option for tattooing. Pen ink is easily accessible and cheap. Still, it is not meant to enter your body in any way, shape, or form. Pen ink is highly toxic and unsterile.
Can you give yourself a tattoo with pen ink and a needle?
Final Thoughts – As you may have noticed, we seriously advise people not to do any DIY, homemade tattoo, especially the stick-and-poke kind with pen ink. This can be seriously dangerous and can put your health at risk. It is always better to go get professionally tattooed than to risk skin and tattoo infection. What we’re trying to say is that DIY tattoos aren’t simply worth it! Also Read:
- 5 Best Stick-and-Poke Tattoo Kits (2022 Updated)
- 6 Stick and Poke Ink Alternatives (And Why You Shouldn’t use Them)
What happens if I tattoo without ink?
Mary McMahon Date: July 11, 2022 
A tattoo machine. When a tattoo machine is used without ink, the resulting mark on the client is known as an inkless tattoo. Depending on how the tattoo is cared for, it will turn into a subtle scar which will disappear entirely in a year or so. There are numerous reasons to choose to get inkless tattoos, and numerous tattoo shops offer them, although they may not advertise the service. 
Numerous tattoo shops offer inkless tattoos, although they may not advertise the service. A tattoo machine uses a vibrating motor to push needles into the skin thousands of times a minute. When the needles are dipped in ink, the result is a tattoo. When the needles are run “dry,” they create a wound which is essentially a series of puncture marks. 
Individuals who receive tattoos in states that do not regulate tattoo facilities should wait 12 months before donating blood. The process of getting an inkless tattoo is similar to that involved in getting a tattoo with ink. The client will still experience the pain and subsequent endorphin release involved in tattooing, and he or she will be left with a mark which has personal meaning.
In the case of an inkless tattoo, the artist runs over the design several times to ensure even coverage, and the client is given specific aftercare instructions, depending on how he or she wants the tattoo to turn out.
Sterile tools are used at all times in professional shops, to ensure that the tattoo does not become infected. Getting this kind of tattoo can be more painful since without the ink, the tattoo needle is not lubricated. 
Applying numbing cream to the area to be inked may help reduce the pain associated with receiving a tattoo. When people get tattoos with ink, they are given aftercare instructions which encourage quick, smooth healing, and these instructions are designed to prevent scarring, as a scar can disfigure a tattoo. In the case of an inkless tattoo, clients are told to abuse the tattoo, picking at the scab which will form and allowing it to dry out to encourage the formation of a scar.
Within a few weeks, the tattoo will have created a distinctive scar which fades in under a year, most typically. For people who want the experience of a tattoo without the permanence, an inkless tattoo is an excellent option.
These designs are also easy to conceal, because they are less bold than tattoos produced in ink, which is a concern for people in some industries. Some people also enjoy the process of fading and healing; for example, the tattoo may commemorate a death or major life event, with the fading of the tattoo signaling a transition for the client.
Not all tattoo artists will perform inkless tattoos, and all tattoo artists are not created equal. If you are interested in getting one, you may want to ask around among friendly tattoo shops who can recommend a shop if they don’t perform the service.
You may also hear an inkless tattoo called a “body etching,” so you may want to ask under both names. Mary McMahon Ever since she began contributing to the site several years ago, Mary has embraced the exciting challenge of being a BeautyAnswered researcher and writer. Mary has a liberal arts degree from Goddard College and spends her free time reading, cooking, and exploring the great outdoors. Mary McMahon Ever since she began contributing to the site several years ago, Mary has embraced the exciting challenge of being a BeautyAnswered researcher and writer. Mary has a liberal arts degree from Goddard College and spends her free time reading, cooking, and exploring the great outdoors.
How do you make a tattoo gun with an electric toothbrush?
How do you get a tattoo without a needle?
A tattoo that is warning you for too many hours of sunlight exposure, or is alerting you for taking your medication? Next to their cosmetic role, tattoos could get new functionality using intelligent ink. That would require more precise and less invasive injection technique.
- Researchers of the University of Twente now develop a micro-jet injection technology that doesn’t use needles at all;
- Instead, an ultrafast liquid jet with the thickness of a human hair penetrates the skin;
It isn’t painful and there is less waste. In there new publication in the Journal of Applied Physics, the scientists compare both the needle and the fluid jet approach. Ötzi the Iceman already had, over 5000 years ago, dozens of simple tattoos on his body, apparently for pain relief.
Since the classic ‘anchor’ tattoo that sailors had on their arms, tattoos have become more and more common. About 44 million Europeans wear one or more of them. Despite its wider acceptance in society, the underlying technique didn’t change and still has health risks.
One or more moving needles put ink underneath the skin surface. This is painful and can damage the skin. Apart from that, needles have to be disposed of in a responsible way, and quite some ink is wasted. The alternative that David Fernández Rivas and his colleagues are developing, doesn’t use any needles. 
.
